A Wilder washer filling for half an hour, a dryer in a farm-labor duplex running cold, a refrigerator on Golden Gate Ave that quit during hop harvest.
Monday–Friday 7:30–5:30 · Saturday 8–1 · closed Sunday

Pick a machine to read what fails around here, how the visit goes, and notes from stops nearby.
Refrigerator & Freezer Repair$99 with a meter · rides inside the repair
Washing Machine Repair$99 with a meter · rides inside the repair
Clothes Dryer Repair$99 with a meter · rides inside the repair
Dishwasher Repair$99 with a meter · rides inside the repair
Range, Oven & Cooktop Repair$99 with a meter · rides inside the repair
Ice Maker Repair$99 with a meter · rides inside the repairThe route to Wilder runs west on Hwy 19 out of Caldwell, through Greenleaf, and into town where Hwy 19 crosses Hwy 95. Golden Gate Ave is the main street, and most in-town stops are within a few blocks of it. The rest are out on the county roads between the hop yards and the orchards, north along Hwy 95 toward Parma or south toward the river. Farm-labor housing, duplexes and older rentals make up a good share of the calls, and a lot of those are approved by an owner who is not on site. Send the gate code, the dog notes and the owner's number in the request, and the tech handles the rest by text and email.
Wilder is hop yards, orchards and row crops, and the houses match: farmhouses on the county roads, small 1940s to 1970s places in the town grid, farm-labor units built in blocks, and a few newer homes on acreage. Everyone outside the town system is on a well, and even in town the water is hard. Sand and iron are common. Ranges out on the farms are propane; in town they split between electric and propane. Harvest season fills the air with dust and the dryer vents with lint, and the July heat finds every garage refrigerator and second freezer. Winter fog off the river ices dryer hoods shut and keeps unheated shops cold enough to thaw a chest freezer.
| Machine | The usual Wilder call |
|---|---|
| Refrigerators | Shop refrigerators out on the farms giving up in July; rental units with a defrost heater gone and the freezer packed in frost. |
| Washers | Sand-packed inlet screens, iron-stained tubs, and hard-used machines in farm-labor housing with worn couplers and pumps. |
| Dryers | Harvest dust in the vent, thermal fuses open, and duplex dryers sharing a vent run that nobody has cleaned. |
| Dishwashers | Scale on the element and film on the glasses; float switches stuck with grit; boards knocked out by a summer outage. |
| Ovens & ranges | Propane ranges on the farms burning yellow; electric ranges in town with a bake element open at one end. |
| Ice makers | Valves narrowed by scale until the fill is a dribble, and fill tubes frozen solid; filters that outlived their date by a year. |
A top-load washer in a farm-labor unit off Golden Gate Ave, needing thirty minutes to reach the fill line. Fine sand had packed both of the inlet screens. Screens cleaned, the hot-side coil metered weak and the valve replaced, fill timed to the mark. The owner approved by text from Caldwell and got the photo and invoice by email.
A refrigerator in a farmhouse between two hop yards, freezer walls packed in frost and the fresh-food side climbing. The meter showed the defrost heater open. A new heater went in from truck stock, evaporator thawed, thermostat and timer checked, and temperatures logged on both sides before the truck left for the next stop.
An electric dryer in a duplex along Hwy 95, tumbling cold. Thermal fuse open, element sound. The shared vent run behind the two units was packed to the hood with lint from both dryers. New fuse, the whole run cleared to the hood, airflow read at the outlet, both tenants told what to watch for.
A propane range in an orchard house south of town, oven lighting well after the gas started flowing. The igniter drew far under the current needed to open the valve. New igniter fitted, cold start timed, burner flames checked, and the old part left on the counter so the homeowner could see the crack.
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Frost an inch thick on the freezer wall of a Wilder rental, a second refrigerator in a farm shop that gave out during hop harvest, a French door in a newer house on acreage clicking on and off all day. Heat, dust from the fields and the occasional brownout do the damage here. The technician meters the compressor and relay, tests the fans and the defrost circuit, tells you which part failed, and the figure written for the repair is one the $99 diagnostic already belongs to.
| The complaint | Behind it, usually | The repair |
|---|---|---|
| Frost packed on the freezer wall | Defrost heater or thermostat failed; the coil never clears | Meter the heater and thermostat, swap whichever is open, clear the ice off the coil, force a defrost cycle |
| Clicks on and off all day | Start relay failing, or a compressor overheating behind a dusty coil | Test the relay and overload, clean the coil, measure amperage under load |
| Second refrigerator in the shop quit in July | Condenser fan stalled or the compressor tripping its overload in the heat | Fit a new fan, clean the coil, and say so straight if it is the compressor that has failed |
Yes. Tenants can book the call and open the door. The owner's phone gets the diagnosis, a photo of the part and a figure in writing, the owner texts back an OK, and if the truck has the part the work is finished before we leave. Invoice and warranty term follow by email to the owner.
Request refrigerator service in Wilder → · Refrigerator & Freezer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
A Wilder washer that hums and never turns the load, a fill that drags on so long the machine gives up, a spin that walks the whole thing away from the wall. Hard-used machines in farm-labor housing and well water full of sand keep the pump, screens and coupler at the top of the list. The technician meters the motor, pump and valve, names the part, and the price comes as a single written figure; the $99 from the diagnosis rolls into it rather than riding on top.
| You see | Likely reason | Our approach |
|---|---|---|
| Hums, load never turns | Coupler sheared or belt slipped; sometimes a motor with a dead start winding | Replace the coupler or belt, meter the motor, run agitate and spin with a load |
| Fill times out and the cycle quits | Inlet screens packed with sand, valve coils weak | Clear both screens, check the coil resistance, put in a new valve, clock the fill |
| Walks away from the wall on spin | Suspension worn, machine out of level, or a load that bunched | Replace the rods or springs, level it on the floor, spin a full load to confirm |
Sand. Wells around Wilder often pull fine sand, and it collects in the two small screens where the hoses meet the valve. Once they pack, the fill slows to a trickle and newer machines throw a timeout code. The technician cleans or replaces the screens and meters the valve on every slow-fill call here.
Request washer service in Wilder → · Washing Machine Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Cold tumbling in a Wilder duplex, a farmhouse dryer that takes a second run for every load, a hood on the north wall frozen shut on a foggy January morning. Harvest dust in the vent is the common thread, and in shared housing two dryers on one vent run make it worse. Airflow gets measured before anything else; after that the technician meters the thermostats, the thermal fuse and the element or igniter. You get one figure in writing, and the $99 from the door is already sitting in it.
| Sign | Usual culprit | Fix |
|---|---|---|
| Tumbles cold in a duplex | Thermal fuse open from a shared, packed vent run | Replace the fuse, clear the whole run to the hood, measure airflow at both machines |
| Second run for every load | Vent restricted, or a cycling thermostat cutting heat early | Clean the duct, meter the thermostat, replace it if it trips low |
| Hood frozen shut in fog | Flap stuck, moisture freezing in a long cold run | Clear and replace the flap, check the run's pitch, advise on shortening it |
Yes, whenever the vent caused the failure. A thermal fuse or a tripping thermostat almost always means restricted airflow, and replacing the part without clearing the duct just sets up the next call. We clear the run, measure airflow at the outlet and note the reading on the invoice.
Request dryer service in Wilder → · Clothes Dryer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Cloudy glasses in a Wilder cupboard, a float switch stuck up with grit so the tub never fills, a control panel that went dark after a summer outage. Well water with sand and scale, and Idaho Power brownouts in a July storm, are behind most dishwasher calls out here. The technician checks the softener, meters the element, valve, float and board, tells you in plain words what failed, and the written price you get has the $99 built into it rather than added on.
| What is happening | Probable cause | What happens on the visit |
|---|---|---|
| Tub never fills, cycle aborts | Float switch stuck with grit, or the inlet valve scaled shut | Unstick and clean the float, meter the valve, replace it, verify a full fill |
| Glasses come out cloudy, element crusted white | Well water scale, often with the softener empty of salt or on bypass | Descale the element and tub, check the softener, tell you what the water needs |
| Dead panel after a thunderstorm | A surge took the thermal fuse or the control board | Test the fuse and board, replace the failed one, suggest a surge protector |
Usually. Pumps, floats, valves and elements are quick parts and the truck carries them for the builder-grade Whirlpool, GE and Frigidaire units that fill those kitchens. At the $99 diagnostic the owner receives a single figure by text and makes the call; a no means the bill ends at $99.
Request dishwasher service in Wilder → · Dishwasher Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
A propane range on a Wilder farm with flames that climb the side of the pot, an electric oven in town that never gets past warm, a burner that sparks and sparks without catching. Out here the technician checks for a bad natural-gas-to-propane conversion first, then meters the igniter, bake element, spark module and sensor. You hear in plain words which part gave out, and the figure the technician writes down for the repair has the $99 folded in already.
| The symptom | Where it usually starts | How we handle it |
|---|---|---|
| Flames climbing the pot on propane | Orifices or regulator still set for natural gas | Fit propane orifices, set the regulator and air shutters, check every burner |
| Electric oven stalls at warm | Bake element open at one end, or an oven sensor that reads high | Meter both, install whichever failed, confirm the temperature with a thermometer |
| Burner sparks but never catches | Ports clogged with grease and dust, or a weak spark module | Clean the ports and cap, test the module, replace the electrode if cracked |
Bake and broil elements, oven sensors and burner switches are still available for most of those ranges and ride on the truck. The technician meters the failed part at the $99 diagnostic, texts the owner a single written figure, and most of these repairs are done before the truck leaves. If the control is gone and discontinued, you hear that plainly.
Request range service in Wilder → · Range, Oven & Cooktop Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
An ice maker in Wilder that stopped somewhere around the start of hop harvest, cubes that come out the size of a fingernail, or a wedge of ice growing where the fill tube enters the freezer. Sand and scale in well water hit the fill valve before anything else, and sand also settles in its screen. The technician meters the valve, measures the fill, checks the filter, tube heater and maker module, then puts one figure on paper; the $99 diagnostic is a piece of that figure, not an add-on.
| Report | Typical fault | Procedure |
|---|---|---|
| Stopped making ice, no sound | Fill valve dead or scaled shut, or the maker module failed | Meter the valve coil, test the module, replace the failed one, confirm a fill |
| Fingernail-sized cubes | Short fill from a narrowed valve, plugged screen or overdue filter | Clean the screen, replace the filter, meter the valve, measure the fill volume |
| Ice wedge at the fill tube | Valve seeping, or the tube heater out | Melt the plug, watch the valve for a seep, replace the valve or the heater |
Sooner than the six months printed on the box. Sand and iron load a filter fast, and a plugged one starves the ice maker before it slows the water dispenser. If cubes are shrinking, the filter is the first suspect; the technician checks it and the valve on every Wilder ice maker call.
Request ice maker service in Wilder → · Ice Maker Repair, the county-wide page →
Yes. Wilder is on the Hwy 19 run with Notus and Greenleaf, and there is no mileage line, no out-of-area fee and no trip charge for a return with an ordered part. The $99 buys the diagnosis. If the repair gets your OK, we do not stack the $99 on top of it; walk away and $99 is all we invoice.
Yes, and we do it often. The tenant opens the door, a photo of the bad part goes to the owner's phone for a text approval, and the owner's inbox gets a copy of the invoice, warranty term printed at the bottom. Put the owner's number and any gate or dog notes in the request.
It coats the heating element in scale so the water never gets hot, packs the filter and spray arms with grit, and leaves a white film on every glass. The technician meters the element, cleans the filter and tells you which is the bigger problem, the dishwasher or the well, before any number goes on paper.
Yes. A yellow flame on propane means the orifices or regulator are still set for natural gas, or an air shutter is closed. The truck carries propane orifice kits for the common brands. The technician converts and adjusts it, checks each burner and the oven, then the price goes on paper as one line, with the $99 diagnostic rolled into that line.
Roughly 12 minutes from Davis Ave · ZIP 83605 · 83607
Open →Roughly 18 minutes from Davis Ave · ZIP 83644
Open →Roughly 22 minutes from Davis Ave · ZIP 83641
Open →Roughly 20 minutes from Davis Ave · ZIP 83656 · 83626
Open →Roughly 30 minutes from Davis Ave · ZIP 83660
Open →Where the truck loads · ZIP 83651
Open →The phone is quicker; the form lands on the same desk. Both get you a text with a window, and until a technician has had a meter on the machine the only figure anyone quotes is $99.
Open the request formRing the shop or fill in the form; dispatch answers with a window, and a text follows as the truck pulls off Davis Ave — first stops go to the Boise commuters, Saturday mornings to everyone else.
Measurements come before opinions: amps at the compressor, degrees on the shelf, ohms across the element. The failed part gets its everyday name from the technician, who then writes the repair as a single figure, $99 folded in.
The shelves on the truck hold what this valley wears out — inlet valves, defrost heaters, heating elements, igniters, drain pumps, rollers. When something must be ordered, the return trip happens on our calendar and the figure you approved stands.
The machine runs a whole cycle while you watch, panels and floor go back the way they were, and the invoice that reaches your email carries the warranty term.
Roughly 25 minutes out from Davis Ave, and the miles never reach the invoice. $99 for the meter, the repair as one figure on paper, warranty term printed on the invoice.