A freezer thawing in a Roswell shed, a dryer on Hwy 95 running cold, a dishwasher on well water that fogs every glass.
Monday–Friday 7:30–5:30 · Saturday 8–1 · closed Sunday
Pick a machine to read what fails around here, how the visit goes, and notes from stops nearby.
Refrigerator & Freezer Repair$99 with a meter · rides inside the repair
Washing Machine Repair$99 with a meter · rides inside the repair
Clothes Dryer Repair$99 with a meter · rides inside the repair
Dishwasher Repair$99 with a meter · rides inside the repair
Range, Oven & Cooktop Repair$99 with a meter · rides inside the repair
Ice Maker Repair$99 with a meter · rides inside the repairParma is the far corner of the map for us. The truck leaves Davis Ave, picks up Hwy 20-26 on the west side of Caldwell, runs through Notus and along the seed fields, and comes into town where Hwy 95 crosses. From there the stops spread out: the older houses on the grid near the school, the farmhouses toward Roswell and the Old Fort Boise park, the places off Hwy 95 north toward the Oregon line. Driveways are long, mailboxes are the address, and a lot of the directions we get end with the words past the onion sheds. We put the whole route on one card. Nothing for the distance goes on the invoice, and an ordered part does not add a second fee.
The housing here is older than most of the county: farmhouses from the 1910s to the 1950s with add-on laundry rooms, a few ranches from the 60s, and a scatter of newer houses on split-off acreage. Almost everything sits on a private well, and Parma well water is hard with enough iron to stain a sink orange. That water is what we fix most. Scale chokes ice-maker fill tubes and the inlet valves on washers, coats dishwasher heating elements until glasses come out chalky, and plugs the screens on washer hoses. A good share of kitchens cook on propane, and a range converted badly burns yellow and blackens pans. Add July heat on a garage freezer and field dust in every dryer vent, and that is the Parma work order.
| Unit | Most common Parma fault |
|---|---|
| Refrigerators | Garage and shed units that quit in the July heat, condenser coils packed with dust off the onion fields, defrost heaters gone open on older side-by-sides. |
| Washers | Inlet screens choked with sand and scale off the well, drain pumps jammed by a stray sock or a length of baling twine, old top-loads with worn couplers. |
| Dryers | Vents full of lint and field dust, thermal fuses blown from restricted airflow, propane dryers with weak igniters and dirty flame sensors. |
| Dishwashers | White film on everything, heating elements crusted with scale, no softener in the farmhouse and a spray arm plugged with grit. |
| Ovens & ranges | Propane ranges burning yellow after a rough conversion, bake igniters grown too feeble to pull the valve open, glass tops with one dead element. |
| Ice makers | Scale that has choked fill valves down to a trickle, fill tubes plugged with ice, small cloudy cubes on iron-heavy water. |
Off Roswell Rd, a farmhouse kitchen side-by-side: freezer fine, fresh side warm. The owner had already thrown out the milk once. We pulled the back panel, found the evaporator packed in frost, metered the defrost heater open and replaced it from the truck. Cold shelf before the tractor came in for lunch.
An electric dryer in a mud room on Hwy 95, tumbling but cold. The vent ran twenty feet under the porch and was solid with lint and field dust. Thermal fuse open, element intact. We replaced the fuse, cleared the run to the outside flap, and showed the owner why the fuse blew in the first place.
A ten-year-old dishwasher a mile from the Old Fort Boise park, glasses coming out white and the bottom rack wet at the end. Well water, no softener. The heating element was crusted so thick it could not reach temperature. New element, a descale cycle, and a frank word about keeping the softener salted.
A top-load washer in a crew house behind a seed farm, filling so slowly it timed out. Both inlet screens were packed with sand and orange scale. We cleaned the screens, metered the valve, and it filled in under a minute. The farm manager approved by text from the field and got the invoice by email.
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Parma is harder on a refrigerator than town is. Garage and shed units sit in a metal building that hits triple digits in July, and the same building drops into the thirties in January so the freezer thaws while the compressor rests. Coils fill with field dust. We meter the compressor, check the fan and defrost circuit, and name the failed part before quoting. Once you approve, the $99 is simply part of the written figure, and that figure only gets written after the diagnosis, never ahead of it.
| Your report | Where it points | The work |
|---|---|---|
| Frost coating the freezer, fresh side losing cold | Defrost heater or defrost thermostat open, evaporator iced solid | Meter the heater and thermostat, replace the failed one, clear the ice, confirm the fan |
| Runs all day in the July heat, never cold enough | Dust and cottonwood fluff matted into the condenser coils, fan tired | Clean the coils, test the fan motor, check compressor amperage under load |
| Garage freezer thawing in a cold January | Garage so cold the thermostat never asks for cooling | Confirm what is happening, talk through a heater kit, or a unit rated for a garage, if either exists |
Often yes. When a unit quits in July the cause is usually a dirty condenser, a fan that died or a start relay that failed, all truck-stock parts. If the compressor meters open, that is another conversation, and it happens before anything gets written. The $99 buys you that answer either way.
Request refrigerator service in Parma → · Refrigerator & Freezer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Parma washers fight the well more than they fight the laundry. A load that takes forever to fill, a machine that fills and then sits, a drum that will not spin with a wet load in it. Sand and iron scale plug inlet screens, and a drain pump only needs one glove or twine end to stop. We open the machine, put the meter on valve, pump and motor, and the repair goes on paper as a single figure, the $99 diagnostic absorbed in advance. Say no and $99 settles it.
| Symptom at the machine | Typical fault | Action taken |
|---|---|---|
| Slow fill, or a fill error before the tub is full | Inlet screens plugged with well sand and scale, valve coil weak | Clean or swap the screens, meter the valve coils, time the fill |
| Tub still full, spin never comes | Blocked or dead drain pump, or a lid lock that refuses to confirm | Unblock or swap the pump, check the lid lock, drain and spin a full load |
| Banging on spin, machine creeping across the floor | Suspension rods or dampers gone soft, unbalanced load | Replace the suspension, level the machine, run a spin with a heavy load |
That is iron from the well, not the washer. It shows up in a machine that sits with water in the tub or that fills through a rusty supply hose. We check the hoses and the tub for sediment, but the real fix is on the water side. We tell you that rather than sell you a part the water will wreck again.
Request washer service in Parma → · Washing Machine Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
A dryer out here breathes the same air as the onion fields, and the vent shows it. Two cycles to dry a load, a drum that is warm but never hot, a burnt smell from behind the machine. Restricted airflow blows the thermal fuse, and on propane dryers a weak igniter or dirty flame sensor kills the burner. The fuse, thermostats and element or burner all get metered, the vent run gets cleared, and the repair is written up as a single figure that already includes the $99.
| What the dryer does | Common reason | Our approach |
|---|---|---|
| Drum turns, air stays cold | Plugged vent that opened the thermal fuse, or a burned-through element | Meter fuse and element, replace what failed, clear the vent to the outside |
| Propane dryer warms up, then loses the flame partway | Flame sensor or gas coils dropping out as they warm up | Check the coils warm and cold, fit a new pair, watch the burner hold |
| Drum squeals or thumps each turn | Worn rollers, idler pulley or belt | New rollers, idler and belt together, then a cycle to prove it runs quiet |
If the vent is what took the dryer down, clearing that run belongs to the repair, and we check the flap outside too. A vent buried under a farmhouse porch or run through a crawl space is the usual find. If the vent needs rebuilding rather than clearing, we tell you that in writing and you decide.
Request dryer service in Parma → · Clothes Dryer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
The first sign of trouble in a Parma dishwasher is usually the glasses. A white haze that will not wipe off, a gritty film on the plates, then water standing in the bottom at the end of the cycle. Hard well water coats the heating element and plugs the spray arms, and older farmhouses rarely have a softener in line. Element, drain pump and wash motor each get tested, whatever scale can be removed is removed, and the job gets a single written price into which the $99 has already gone.
| How it shows | Likely source | Fix applied |
|---|---|---|
| Glasses chalky, plates not clean | Scale on the element and inside the spray arms, wash arm holes blocked | Descale the tub and arms, test the element, check water temperature at the inlet |
| Pool in the bottom at the end | Grit and seed hulls in the drain pump, stuck check valve | Unjam or swap the pump, clean out the sump, check the hose loop |
| Cycle ends early or never starts | Door latch switch, control board damaged by a summer power bump | Test the latch, meter the board inputs, replace the failed part |
It does more than any repair we can sell you. Softened water stops scale from building on the element and inside the arms, and the rinse aid can do its job. We are not softener installers, but the scale on the element is something we will hold up so you can see what the water is doing before you decide.
Request dishwasher service in Parma → · Dishwasher Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Parma kitchens are propane country. A burner that lights yellow and leaves black on the bottom of the pan, an oven that clicks for a minute and then smells of gas, a bake element on an electric range that glows at one end only. Most of it comes back to a rushed propane conversion, a bake igniter that has gone weak with age, or a switch that failed. We test the igniter under load, check the burner flame, and the repair comes back as one figure, the $99 already in it.
| Kitchen complaint | Usual suspect | Steps we take |
|---|---|---|
| Oven clicks, gas smell, no flame | Igniter grown too weak to pull the oven's safety valve open | Read the igniter's current draw, swap it, time the ignition and check the flame |
| Yellow flames, soot on the pans | Propane conversion done without the right orifices or regulator setting | Check orifices and regulator, correct the air shutter, set a clean blue flame |
| Electric oven runs cold or bakes uneven | Burned-out bake element, or a sensor that has drifted | Meter both element and sensor, swap whichever failed, prove the oven holds temperature |
We can correct a range that was converted and now burns badly, and we can complete a conversion on a range that has the kit for it. Orifices, regulator and every burner's flame get checked before the truck leaves. The one thing we will not do is run or connect the propane line itself; that is the gas company's side.
Request range service in Parma → · Range, Oven & Cooktop Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
An ice maker on Parma well water works against scale every fill. The cubes get small and cloudy, then the tray stops filling, then the fill tube behind the freezer wall turns into a plug of ice. On iron-heavy water the fill valve can narrow to a trickle in a couple of years. We test the fill valve, thaw and inspect the tube, check the mold thermostat, and the repair lands on paper as a lone figure, the $99 diagnostic absorbed before the ink dries.
| Ice trouble | Most likely cause | Remedy |
|---|---|---|
| No ice, tray dry | Fill valve scaled shut, fill tube frozen, or the maker itself failed | Meter the valve, thaw the tube, test the maker cycle, replace what failed |
| Small hollow cubes, slow production | Low water flow through a narrowed valve or a blocked inline filter | Measure flow at the valve, swap filter or valve, watch for a full fill |
| Ice tastes of iron or looks orange | Well water and an old inline filter | Replace the filter, flush the line, talk about treatment at the house side |
Two reasons stack up in July. The freezer is working hard in a hot house or garage so the mold never reaches the cold it needs to drop the cubes, and the fill valve is already restricted by scale so each fill is short. Freezer temperature gets checked first, the valve second, and fix the one that is actually failing.
Request ice maker service in Parma → · Ice Maker Repair, the county-wide page →
Yes. Parma is inside our service area, and the card does not change with the address. The $99 covers the diagnosis at the machine. Say yes to the written figure and the $99 is buried in it rather than stacked on top. Turn it down, and your bill ends at $99. No mileage line, and nothing is added for the drive back with an ordered part.
We service gas ranges on propane all over the west end of the county. A range that came from a store set for natural gas and was converted in a hurry usually burns yellow, soots the pans and runs the oven cold. We check the orifices, the regulator setting and the igniter, and put the burners back to a clean blue flame.
Iron-heavy hard water chokes ice-maker fill lines and washer inlet valves, crusts the dishwasher element, and fogs every glass. Sand from the well plugs inlet screens on washers. None of that is the machine's fault, and most of it is fixable. We tell you which parts the water killed and what will slow it down next time.
A warm refrigerator or freezer called in before noon gets a same-day window if we can build it into the route. Everything else in Parma is usually same-week, often the next day. You get an arrival window by text, and the technician phones as the truck pulls away from the stop before yours, so nobody sits waiting where a long driveway ends.
Roughly 12 minutes from Davis Ave · ZIP 83605 · 83607
Open →Roughly 18 minutes from Davis Ave · ZIP 83644
Open →Roughly 22 minutes from Davis Ave · ZIP 83641
Open →Roughly 20 minutes from Davis Ave · ZIP 83656 · 83626
Open →Roughly 25 minutes from Davis Ave · ZIP 83676
Open →Where the truck loads · ZIP 83651
Open →The phone is quicker; the form lands on the same desk. Both get you a text with a window, and until a technician has had a meter on the machine the only figure anyone quotes is $99.
Open the request formRing the shop or fill in the form; dispatch answers with a window, and a text follows as the truck pulls off Davis Ave — first stops go to the Boise commuters, Saturday mornings to everyone else.
Measurements come before opinions: amps at the compressor, degrees on the shelf, ohms across the element. The failed part gets its everyday name from the technician, who then writes the repair as a single figure, $99 folded in.
The shelves on the truck hold what this valley wears out — inlet valves, defrost heaters, heating elements, igniters, drain pumps, rollers. When something must be ordered, the return trip happens on our calendar and the figure you approved stands.
The machine runs a whole cycle while you watch, panels and floor go back the way they were, and the invoice that reaches your email carries the warranty term.
Roughly 30 minutes out from Davis Ave, and the miles never reach the invoice. $99 for the meter, the repair as one figure on paper, warranty term printed on the invoice.