Upstairs washer dripping through the ceiling, dishwasher scaled up in a house that is four years old, dryer venting through the roof and taking two cycles.
Monday–Friday 7:30–5:30 · Saturday 8–1 · closed Sunday

Pick a machine to read what fails around here, how the visit goes, and notes from stops nearby.
Refrigerator & Freezer Repair$99 with a meter · rides inside the repair
Washing Machine Repair$99 with a meter · rides inside the repair
Clothes Dryer Repair$99 with a meter · rides inside the repair
Dishwasher Repair$99 with a meter · rides inside the repair
Range, Oven & Cooktop Repair$99 with a meter · rides inside the repair
Ice Maker Repair$99 with a meter · rides inside the repairSouth and West Meridian is the part of Ada County that starts where Nampa ends. The truck takes I-84 east to the Ten Mile exit, runs Overland Rd across the county line, or comes up from Kuna on Lake Hazel Rd. The work is in the square miles between Ten Mile Rd and the freeway, south along Amity and Lake Hazel, where farmland turned into subdivisions between the early 2000s and last year. Nearly every house is two stories with the laundry upstairs, a spare refrigerator out in the garage and a builder package in the kitchen. Most people here drive to Boise for work, so the early stop is first on the calendar and we text before the truck turns off Ten Mile.
The water is Meridian city water, hard groundwater like the rest of the valley, and the softener in the garage is the difference between a dishwasher that lasts and one that scales up in a year. The lawns run on pressurized irrigation from the Nampa and Meridian district canals, which is a separate pipe and not what feeds the kitchen. What we fix here is what a second-floor laundry produces: drain pumps that quit and trip the flood pan, torn door boots, dryers vented through the roof and never cleared. Add ice makers narrowed by scale, garage refrigerators on the sunny side of the house, and control boards that took a summer thunderstorm on the chin. Rentals are common and the owner often approves from an office across town.
| Machine | What breaks in these subdivisions |
|---|---|
| Refrigerators | Builder French doors with dead evaporator fans, garage second refrigerators overheating in August, boards knocked out by summer storm outages. |
| Washers | Upstairs front-loaders with dead drain pumps and sliced door boots, a stain on the ceiling underneath, stacked pairs in hall closets. |
| Dryers | Lint-packed runs up through the roof, open thermal fuses, moisture sensors filmed over with softener residue. |
| Dishwashers | Builder units scaled up after the softener ran dry, drain pumps blocked, panels dark after a brownout. |
| Ovens & ranges | Gas ranges with weak bake igniters, glass tops with a dead radiant element, wall ovens with a failed relay board. |
| Ice makers | Scale-choked fill valves, door makers iced up at the chute, makers the control switched off during an outage. |
Upstairs laundry room off Amity Rd, front-load washer, and a water stain spreading across the dining room ceiling underneath. The door boot had a slit from a jeans rivet and the flood pan drain was never connected. New boot, pan drain corrected, and a full cycle watched from the room downstairs to be sure.
An electric dryer in a 2016 house near Lake Hazel Rd, running cold with a burnt smell. The vent went straight up two floors to a roof cap that had never been opened. Thermal fuse open, element intact. We replaced the fuse, cleared the run to the cap, and left a small pile of lint on the drive as evidence.
A builder-package dishwasher in a rental near Overland Rd, tenant reporting white glasses and a sour smell. The owner approved the visit by text from work. Softener bypassed, element crusted with scale. Element replaced, tub descaled, softener valve set right, and the invoice and warranty emailed to the owner before the tenant got home.
A second refrigerator in a west-facing garage off Ten Mile Rd, warm in a week of triple-digit afternoons. The condenser was blanketed in dust and the fan had quit. Fan and start relay replaced from the truck, coils cleaned, and a suggestion to pull it a hand's width off the wall so it can breathe.
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Refrigerators in South and West Meridian are mostly the French-door builder models that came with the house, plus the older unit that moved out to the garage. The kitchen machine fails at the evaporator fan, the defrost system or a control board after a storm outage; the garage one cooks in August against a west wall. Compressor, fans and defrost circuit are each metered before anything gets a name. Approve the work and the $99 is simply part of the total; that total only ever appears in writing once the diagnosis is done.
| The call | Common fault | Technician does |
|---|---|---|
| Freezer fine, fresh side going warm | Evaporator fan iced up or dead, or a stuck damper | Check fan and damper, swap what failed, feel for cold air at the shelves |
| Dead panel after a thunderstorm | Main control or inverter board taken out by the surge | Meter the boards, fit a new one, watch the compressor start and hold |
| Garage refrigerator warm in the afternoon heat | Dust-blocked condenser, dead fan or relay | Brush out the condenser, swap the fan or relay, read amperage with the compressor loaded |
Generally yes. Fans, defrost heaters, relays and boards are all truck-stock parts and the cabinet and compressor have years left. The one case where the number gives people pause is a sealed-system leak, and that news comes at the diagnosis, when $99 is still the only figure in play.
Request refrigerator service in South & West Meridian → · Refrigerator & Freezer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Almost every washer we see in South and West Meridian is a front-load on the second floor. Water showing at the door, a drain code on the display, a stain on the ceiling below, or a spin that shakes the whole house. Drain pumps choked with hair ties, door boots cut by rivets, bearings gone after a slow seal leak. Pump, motor and valve are all metered, the flood pan is inspected, and the repair is written up as a lone figure with the $99 already absorbed. Say no and $99 is where it ends.
| Reported problem | Likely part | Repair on the day |
|---|---|---|
| Drain code, load left soaking | Drain pump jammed or burned out, filter stuffed with debris | Empty the filter, meter the pump and fit a replacement, drain and spin a load |
| Water under the machine or on the ceiling below | Door boot cut, dispenser hose split, pan drain never connected | Swap the boot or hose, hook up or clear the pan drain, run a whole cycle to check |
| Spin sounds like an airplane | Tub bearings failed after the seal let water through | Confirm it at the drum, put the bearing and seal figure on paper before the tub comes apart |
Yes. The boot comes out from the front with the machine in place, and the drain filter behind the lower panel is where we find the object that cut it. A bearing job is a different matter and sometimes needs the machine pulled out into the hall, which we tell you about before the number gets written.
Request washer service in South & West Meridian → · Washing Machine Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
The dryer on a second floor in South and West Meridian vents straight up, attic and all, to a cap on the roof, and nobody has looked at that cap since the closing. Clothes come out damp, the laundry room gets hot, and one day the drum tumbles cold because the thermal fuse gave up. Softener residue coats the moisture sensor so the auto cycle stops early. Fuse, thermostats and heat source get metered, the vent gets opened up, and the repair is handed over as one figure that has already soaked up the $99.
| What happens | Cause we find | Fix |
|---|---|---|
| Tumbles cold | Roof vent blocked until the thermal fuse opened, or an element or igniter that died | Check fuse and heat source, swap the failed one, open the vent all the way to the cap |
| Auto cycle stops with the clothes still damp | Moisture sensor bars coated, vent restricted | Wipe the sensor bars, clear the run, check the sensor circuit |
| Squeal from the back | Idler pulley or rear bearing worn | Replace the idler and belt, check the bearing and rollers, run a quiet cycle |
Because the vent runs up two floors and through the roof, and lint has been collecting in it since the first load. Once the vent chokes, the dryer runs hot and slow until the thermal fuse lets go. When the vent brought the failure on, clearing it is part of the job, and you get to look at what came out.
Request dryer service in South & West Meridian → · Clothes Dryer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
A dishwasher in a South or West Meridian house is a builder package installed next to a softener, and the softener is the story. When it runs out of salt or sits on bypass, city water coats the element and fogs every glass within a season. Then a drain pump stopped by a broken glass, a panel dark after a brownout, a cycle that quits early. Element, pump and board are all tested, the scale comes off whatever is worth keeping, and the figure we write already contains the $99.
| Trouble sign | Behind it | Work done |
|---|---|---|
| White glasses, gritty racks | Element scaled over, softener empty or on bypass | Meter the element, strip scale from tub and arms, look at how the softener valve is set |
| Puddle left once the cycle ends | Blocked drain pump, disposal knockout never punched out, plugged air gap | Unblock the pump and the drain path, fix the disposal connection, watch it drain |
| Cycle stops partway, lights blink | Failed thermistor or control board, or a latch that never confirms | Meter sensor and board, check the latch, swap whichever failed |
Two things. Look at the softener salt level in the garage, because an empty softener shows up in the dishwasher first. And run the kitchen tap hot before starting a cycle so the machine begins with hot water. If the glasses are still white and the tub still holds water after that, the element or pump is the likely cause and we come to meter it.
Request dishwasher service in South & West Meridian → · Dishwasher Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Kitchens in South and West Meridian have a gas range or a slide-in glass top from the builder package, and the newest houses are adding wall ovens and induction. The gas oven takes a full minute to light or drops out mid-roast, a glass-top zone heats on one side, the wall oven shows a code and locks the door. We put the igniter under load with a meter on it, test radiant elements and relay boards, and look at every burner's flame. The repair becomes one line on paper, and that line already contains the $99 diagnostic.
| Oven or cooktop symptom | Probable failure | Our fix on site |
|---|---|---|
| Oven takes forever to light, loses flame mid-bake | Bake igniter no longer pulling enough to hold the safety valve open | Read igniter current, swap it, time the ignition and run a whole bake |
| Glass-top burner dead or uneven | Radiant element open or the relay board dropped that zone | Meter element and board, swap the bad one, check heat at the surface |
| Wall oven code, door locked | Temperature sensor out of range, control board or lock motor failed | Pull the code, meter the sensor, cycle the lock, swap the failed part |
Yes. Single or double, gas or electric, wall ovens are on the list. The failures are usually the temperature sensor, a relay board or the door lock, and the display code points the meter at the first suspect. If the oven is still inside the maker's own coverage, we tell you first so you can use it.
Request range service in South & West Meridian → · Range, Oven & Cooktop Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Ice makers in South and West Meridian are mostly the door-mounted kind in French-door builder refrigerators, and they fail from two directions. City water builds scale in the fill valve until every fill runs short and the cubes turn out hollow; the door ice room freezes at the chute when the flap stops sealing. Metering the valve, thawing and checking the tube, testing the chute and fan, and running a full harvest is the visit. The written price already holds the $99; say no to the work, and the bill is $99 and no more.
| Ice symptom | Root cause | What we handle |
|---|---|---|
| Bin dry for days | Scale sealed the fill valve, the tube iced over, or an outage shut the maker off | Put a meter on the valve, thaw the tube, reset the maker and run it, swap what failed |
| Dispenser jammed, ice frozen into a block | Chute flap that no longer seals, a stalled ice-room fan, a freezer running warm | Check flap and fan, sort out the cooling first, clear and dry the chute |
| Cubes undersized and cloudy | Flow choked at the valve or by a tired inline filter | Measure flow, swap filter or valve, watch for a complete fill |
Sometimes not. Some controls turn the maker off after an outage and it stays off until reset. Try the ice-maker switch or the panel setting first. If it is switched on and still makes nothing, the fill valve or the maker itself has failed, and that is what the $99 visit meters and prices in writing.
Request ice maker service in South & West Meridian → · Ice Maker Repair, the county-wide page →
Yes. The stretch from Ten Mile Rd south to Lake Hazel Rd and along Overland and Amity is on our route most days, either off I-84 or across the county line on Overland. It is the Ada County edge of our ring and it carries the same card: $99 to diagnose, and once you say yes that $99 lives inside the repair figure; no mileage line.
The first stop of the day is set aside for exactly that. Ask for it when you call or on the form, and the technician texts before leaving Nampa so you know when to expect the truck. If the repair needs a part from the warehouse, we schedule the return visit the same way and there is no second fee for it.
Shut the water valves behind it and call. On the visit we find the source, usually a door boot, a dispenser hose or a drain pump housing, and we check whether the flood pan drain was ever connected, because in a lot of these houses it was not. You get a lone figure in writing, the $99 folded in ahead of time.
The tenant opens the door, the technician gets the meter onto the machine, and the owner receives a text naming the failed part in plain words along with a single written price. A yes by text and the repair is usually done on that same visit; invoice and written warranty then land in the owner's email. A no means the bill stops at $99.
Roughly 20 minutes from Davis Ave · ZIP 83634
Open →Roughly 25 minutes from Davis Ave · ZIP 83669
Open →Roughly 20 minutes from Davis Ave · ZIP 83639
Open →Roughly 28 minutes from Davis Ave · ZIP 83628
Open →Where the truck loads · ZIP 83651
Open →Roughly 7 minutes from Davis Ave · ZIP 83687
Open →The phone is quicker; the form lands on the same desk. Both get you a text with a window, and until a technician has had a meter on the machine the only figure anyone quotes is $99.
Open the request formRing the shop or fill in the form; dispatch answers with a window, and a text follows as the truck pulls off Davis Ave — first stops go to the Boise commuters, Saturday mornings to everyone else.
Measurements come before opinions: amps at the compressor, degrees on the shelf, ohms across the element. The failed part gets its everyday name from the technician, who then writes the repair as a single figure, $99 folded in.
The shelves on the truck hold what this valley wears out — inlet valves, defrost heaters, heating elements, igniters, drain pumps, rollers. When something must be ordered, the return trip happens on our calendar and the figure you approved stands.
The machine runs a whole cycle while you watch, panels and floor go back the way they were, and the invoice that reaches your email carries the warranty term.
Roughly 18 minutes out from Davis Ave, and the miles never reach the invoice. $99 for the meter, the repair as one figure on paper, warranty term printed on the invoice.