A refrigerator below Lizard Butte that went warm, a dryer in an orchard house running cold, a dishwasher on well water leaving chalky glasses.
Monday–Friday 7:30–5:30 · Saturday 8–1 · closed Sunday
Pick a machine to read what fails around here, how the visit goes, and notes from stops nearby.
Refrigerator & Freezer Repair$99 with a meter · rides inside the repair
Washing Machine Repair$99 with a meter · rides inside the repair
Clothes Dryer Repair$99 with a meter · rides inside the repair
Dishwasher Repair$99 with a meter · rides inside the repair
Range, Oven & Cooktop Repair$99 with a meter · rides inside the repair
Ice Maker Repair$99 with a meter · rides inside the repairKarcher Rd leaves Nampa as Hwy 55, runs west through the orchards and vineyards on the Sunnyslope bench, and drops down to the Snake River bridge into Marsing. The bridge is the county line; on the far side you are in Owyhee County and the truck is still on the same card it carries in Nampa. Stops spread out from Main St along the river road toward Island Park, up the benches below Lizard Butte, and down the county roads between the vineyards. Nothing for the river crossing or the highway goes on the invoice. If the house is at the end of an orchard lane or behind a locked gate, put it in the request.
Marsing houses run from old farm places among the orchards to newer homes on the benches with a view of the river, and outside the small city system most of them draw from a well. That well water is hard, sometimes carries iron, and in a few spots brings up sand that ends up in an inlet valve screen. Propane tanks feed most of the ranges and some of the dryers. Summer here is a long stretch of triple-digit afternoons, and garage refrigerators, chest freezers and ice makers are the first to fold. Winter fog settles in the river bottom and freezes dryer vents. Wind off the Owyhees keeps dust moving through every condenser coil in town.
| Trouble | The Marsing version of it |
|---|---|
| Refrigerators | Refrigerators in bench garages that quit on the first 100°F day; inverter compressors knocked out by a thunderstorm brownout. |
| Washers | Slow fills from sand and scale in the inlet screens; suspension rods worn out on machines that shake an old farmhouse floor. |
| Dryers | Vents frozen shut in January river fog, packed with orchard dust by July; propane dryers with weak igniters. |
| Dishwashers | Scale on the element and a white film on glasses; softeners that were never installed in the older places. |
| Ovens & ranges | Propane ranges burning yellow, oven igniters that cannot pull the valve open, glass tops with a dead radiant element. |
| Ice makers | Scale closing the fill valve down to a thread, filters overdue, fill tubes frozen into a plug during a cold snap. |
A French-door refrigerator on the bench below Lizard Butte, cooling on one side and warm on the other after a July storm knocked the power out for an hour. The inverter board had not come back. Board metered against the compressor, replaced from the truck, temperatures logged on both sides before the invoice went to email.
An electric dryer in a house at the end of an orchard lane, taking two full cycles for a load of work clothes. The vent had a screen at the outlet packed with fuzz and orchard dust. Screen removed and replaced with a proper hood, duct cleared, cycling thermostat tested, one cycle to dry again.
A dishwasher near Island Park leaving every glass white and the water barely warm. Element coated in scale from well water, resistance reading high. New element fitted, tub descaled, a full heated cycle run with a thermometer on the rack, and the homeowner shown where the softener bypass valve was sitting.
A propane range in a newer house between the vineyards, oven taking far too long to light and dropping the door with a thump. Igniter reading well under spec. Igniter replaced, ignition timed cold, each burner checked for flame color, and the invoice with the written warranty sent by email.
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Freezer holding, fresh-food compartment warming up, or the whole box went quiet after a storm rolled through the river valley, or a garage refrigerator on the bench gave out in the first week of triple digits. Marsing refrigerators face heat, dust and the occasional brownout, and the board, the compressor, both fans and the defrost circuit all meet the meter before the technician names what failed. The figure comes in writing, the $99 from the diagnosis already sitting in it, and the bridge crossing nowhere on it.
| What you see | Usual reason | Our steps |
|---|---|---|
| Freezer cold, refrigerator section warm | Evaporator fan stopped, or the damper between the two stuck closed | Meter the fan motor, test the damper, replace the failed one and log both temperatures |
| Box silent after a power blip | Surge took out the inverter or the main control board | Check incoming power, meter the board outputs against the compressor, replace the board |
| Compressor hot to the touch, box barely cool | Condenser coil blanketed in dust, fan motor weak | Clean the coil, replace the fan if it is slow, measure amperage before and after |
The common ones. Evaporator fans, defrost heaters, damper assemblies and the inverter boards for the popular models ride on the truck, because a second trip over the bridge helps nobody. When a part is on order, coming back to fit it runs on the figure you already approved and nobody pays for a second diagnosis.
Request refrigerator service in Marsing → · Refrigerator & Freezer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
A front-loader in a Marsing garage that stops with a code and a tub full of water, a top-loader in an orchard house that fills for half an hour, a machine that walks a foot across the floor on every spin. Washers here deal with well water, sand and long runs of hose, and the technician starts at the inlet screens and drain pump before the motor or board. What you get is a single figure in writing, and the $99 diagnostic lives inside that figure.
| Complaint | Likely cause | Repair |
|---|---|---|
| Quits partway through with a drain code | Drain pump jammed, or the pump filter packed with grit and lint | Clear the filter and pump, meter the pump motor, put in a new pump if its winding reads open |
| Long fill, then a timeout error | Inlet screens plugged with sand, or a weak valve coil | Scrub the screens, check both coils, swap in a new valve, stopwatch the fill |
| Banging on spin, drum has play | Bearing or spider arm failed on a front-loader; rods on a top-loader | Check the drum play, price the bearing job plainly, or replace the rods |
Sometimes. A bearing job means pulling the tub, and on some machines that is most of a day. The technician checks the drum play at the $99 diagnostic, writes one number for the job, and says plainly if the machine's age makes it a poor bet. The choice is yours once you see the figure.
Request washer service in Marsing → · Washing Machine Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Cold air out of the drum in a house by Island Park, a January morning when the dryer runs and the vent is a block of ice, a propane dryer that glows but never lights. Marsing dryers get orchard dust in summer and river fog in winter, and the vent takes the punishment. The technician measures airflow, meters the element or igniter and the thermal fuse, clears the duct, and the written price you get already carries the $99 from the diagnostic.
| Symptom | Behind it | What the technician does |
|---|---|---|
| Vent iced over on a foggy morning | Moist exhaust freezing at a hood with a stuck flap or a long uninsulated run | Thaw and clear the hood, replace a stuck flap, advise on the run so it drains |
| Heats, then goes cold halfway through | Cycling thermostat or high-limit tripping from restricted airflow | Clean the duct, meter the thermostats, replace the one that trips early |
| Propane dryer glows, no flame | Gas valve coils or flame sensor failed | Meter the coils and sensor, replace them, confirm ignition through several starts |
Yes. Propane dryers use the same igniter, coils and flame sensor as natural gas units, with a different orifice, and we carry those parts. If a dryer was converted and never had the orifice changed, it burns hot and trips the high-limit; the technician spots that at the diagnostic and puts the fix in the written number.
Request dryer service in Marsing → · Clothes Dryer Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
Heating element wearing a white crust visible through the lower rack, dishes still wet and cold at the end, water pooled in the sump of a dishwasher in a Marsing farmhouse. Well water without a softener is the story behind most dishwasher calls across the river, and the technician meters the element and inlet valve first, then the pump and board. The repair comes as one number on paper, the $99 diagnostic part of it and the drive absent from it.
| Observed | Generally | Fix applied |
|---|---|---|
| Load comes out cold and dripping | Element crusted with scale or open; the dry cycle never gets hot | Meter the element, descale or replace it, run a heated cycle with a thermometer |
| Water in the sump, will not drain | A pit or a chip of glass in the drain pump, or the check valve jammed | Clean out pump and check valve, then time the drain on a test cycle |
| Fills, then stops and blinks | Inlet valve too slow from scale, float switch stuck, or a door latch fault | Meter the valve and float, clean or replace, verify the cycle runs through |
On most wells here, yes. Without one the element scales, the spray arms clog and no detergent on the shelf keeps the glasses from turning chalky. The technician can descale and replace what has failed, and will say plainly whether the water will do it again in a year without treatment.
Request dishwasher service in Marsing → · Dishwasher Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
The oven in a Marsing farmhouse takes far too long to light and thumps when it does, a burner on the propane cooktop throws a lazy yellow flame, or the electric range in a newer bench house shows an F-code and quits. Propane is the fuel across most of the river side, and the technician's first check is whether the range is still set up for natural gas. Then the igniter, elements and sensor get metered, and you get the repair total in writing; look for the $99 diagnostic inside that total, never under it.
| At the range | Common cause | Our work |
|---|---|---|
| Oven lights late and thumps | Oven igniter below spec, gas building before it catches | Meter the igniter current, replace it, time a cold ignition |
| Lazy yellow burner flame on propane | Wrong orifices or regulator setting for propane; air shutter closed | Install propane orifices, adjust the regulator, open the shutters, check every burner |
| F-code and the oven shuts down | Oven sensor drifted out of range, or a stuck relay on the board | Check the sensor's resistance, replace it or the board, prove it with an oven thermometer |
All three. Wall ovens are pulled from the cabinet when the repair needs it and set back level. Cooktops, gas or glass-top, are lifted from the counter for element and valve work. The technician brings the common igniters, elements and sensors over the bridge so most jobs finish in one visit.
Request range service in Marsing → · Range, Oven & Cooktop Repair, the county-wide page →
$99 to meter it, and that $99 rides inside the repair total · no figure before the meter, none off paper
The ice bin in a Marsing kitchen has been empty since the heat set in, or the maker drops a few cloudy pebbles a day, or there is a frozen stalactite where the fill tube meets the tray. Well water narrows the fill valve until it barely passes water, and the small cubes are the sign. The technician meters the valve, measures the fill, checks the tube heater and filter, and the single figure written for the repair already accounts for the $99 diagnostic.
| Ice maker sign | Probable fault | How we fix it |
|---|---|---|
| Ice stops in the hottest weeks | Dirty coil letting the freezer run warm; the mold stays too warm to harvest | Clean the coil, check the freezer temperature, test the maker's thermostat |
| A few cloudy pebbles a day | Fill valve scaled, filter overdue, low fill volume | Replace the filter, meter and replace the valve, measure the fill into a cup |
| Ice column at the fill tube | Tube heater failed or the valve seeping between cycles | Thaw the tube, test the heater and valve, replace what has failed |
An ice maker needs the freezer colder than the food does. When the condenser coil is dusty and the garage is 100°F, the freezer drifts a few degrees warm, the mold stalls above harvest temperature, and ice stops while food stays frozen. Cleaning the coil is often the whole fix, and the technician confirms with a thermometer.
Request ice maker service in Marsing → · Ice Maker Repair, the county-wide page →
No. The Snake River bridge on Hwy 55 is part of the route, not a line on the bill. Marsing is on the same card as Nampa: no mileage, no out-of-area fee, no trip charge for a return visit with an ordered part. Approve a repair and the $99 from the diagnostic is folded into that figure rather than added.
Marsing and Homedale are both on the list, and they are in Owyhee County. The technician crosses the bridge with the same truck stock and the same written price and written warranty. If you are farther out toward the Owyhee front, call and dispatch will tell you whether the address fits the route.
It scales up the small openings first: the refrigerator fill valve, the ice maker line, the dishwasher inlet and heating element. Iron stains the washer tub and sand fills the inlet screens. The technician checks those before anything else and tells you whether the repair will last on that water.
Yes if it is called in before noon. The truck heads west on Karcher and over the bridge with the common relays, fans and boards on board. The technician meters the compressor and checks the coil, names the part, and the figure that goes on paper has already absorbed the $99.
Roughly 20 minutes from Davis Ave · ZIP 83634
Open →Roughly 25 minutes from Davis Ave · ZIP 83669
Open →Roughly 18 minutes from Davis Ave · ZIP 83642
Open →Roughly 28 minutes from Davis Ave · ZIP 83628
Open →Where the truck loads · ZIP 83651
Open →Roughly 7 minutes from Davis Ave · ZIP 83687
Open →The phone is quicker; the form lands on the same desk. Both get you a text with a window, and until a technician has had a meter on the machine the only figure anyone quotes is $99.
Open the request formRing the shop or fill in the form; dispatch answers with a window, and a text follows as the truck pulls off Davis Ave — first stops go to the Boise commuters, Saturday mornings to everyone else.
Measurements come before opinions: amps at the compressor, degrees on the shelf, ohms across the element. The failed part gets its everyday name from the technician, who then writes the repair as a single figure, $99 folded in.
The shelves on the truck hold what this valley wears out — inlet valves, defrost heaters, heating elements, igniters, drain pumps, rollers. When something must be ordered, the return trip happens on our calendar and the figure you approved stands.
The machine runs a whole cycle while you watch, panels and floor go back the way they were, and the invoice that reaches your email carries the warranty term.
Roughly 20 minutes out from Davis Ave, and the miles never reach the invoice. $99 for the meter, the repair as one figure on paper, warranty term printed on the invoice.